autoriv fasteners automation a100 setting head press tool press application transfer die tool progressive die clinch stud screw bolt sheet metal component workpiece

Setting head for clinch studs, countersunk clinch studs

Installation under the press in punching and forming tools

The setting head FHS (Flat Head Stud) is an assembly system for progressive dies and transfer dies. The punching head is installed in the press to insert clinch studs into sheet metal components during the press process.

Depending on the type of tool and the press, there are different applications for the punching head

  • Progressive dies with or without automatic mode signal from the press
  • Transfer dies, with or without automatic mode signal from the press and with querying sheet metal in the die or in the gripper

Contact us

Our customer service will help you with any questions!

+49 (0) 941 6042-210

Contents

  1. Highlights
  2. Installation and processing
  3. Components
  4. Function
  5. Technical data

Highlights

Processing of bolts with difficult geometry

Thanks to the special screw transport system, it is also possible to process clinch studs with a ratio of diameter equal to length of stud. This is not possible with many other systems.

High production reliability and quality

All important functions in the setting head are sensor-monitored with communication to the feeding system to stop the press in case of a malfunction well before top dead center (TDC) and thus avoid die damage.

Fast stroke rates

If a clinch stud is in the setting position and still being processed, the next stud can already be reloaded. The next fastener can therefore be shot into the setting head in parallel with the processing of one fastener. This means that higher processing speeds can be achieved even with long shot hose lengths.

Safety during coil changes and with empty parts in production (transfer dies).

The screw transport only moves to the set position when a clinch stud is to be installed. Transfer die: If there is no workpiece, the feed cylinder does not move to the set position. It moves when a workpiece is present. The empty part sensor is either in the transfer grippers or in the tool itself. Coil change: When a coil change is required, the feed cylinder remains in the home position and the coil can be retracted as if there were no setting head installed in the tool.

Quick commissioning

The setting head has quick-release couplings for the shot hose and the multifunction hose for communication with the feeding system. There is no need to connect individual cables. This saves time and eliminates connection errors.

Installation and processing

autoriv fasteners automation a100 fhs installation setting head press tool press application transfer die tool progressive die clinch stud screw bolt sheet metal component workpiece
1. Clinching from above; 2. Clinching from below

The setting head processes screw-type fasteners with a head that are inserted with the shank first.

The punching head can be installed in the tool so that clinch studs can be set in the sheet metal from either top or bottom.

When pressing top-down, the upper part of the tool is needed to adjust a setting head. When pressing from the bottom up, the lower part of the tool is required.

The punching head is ready to use immediately after installation. No initialization routine is required.

Components

autoriv fasteners automation a100 fhs setting head press tool press application transfer die tool progressive die clinch stud screw bolt sheet metal components workpiece
1. Connector plug; 2. Plunger (press-in mandrel); 3. Impact piece; 4. Multifunctional hose connector; 5. Feed cylinder; 6. Screw transport

Connector plug (1)

The connector plug is used to connect the shot tube to the setting head. The coupling is held in place by a locking pin on the connector plug of the punching head. The clinch stud is transported via the screw feed (bent tube) into the screw transport.

Plunger (2)

The plunger houses the press-in mandrel, which presses the clinch studs into the sheet metal component. The mandrel is actuated by closing the press and transmits the compression force to the fastener. When the press is opened, the mandrel is pneumatically returned to the home position.

Impact piece (3)

The impact piece guides the fastener during the press-in process.

Multifunctional hose connector (4)

All signals are transmitted from the setting head to the feeding system via the multifunctional hose. The multifunctional hose also provides pneumatic supply to the punching head.

Feed cylinder (5)

The setting head has no accumulation path. The clinch studs are shot directly into the grippers of the screw transport.

Screw transport (6)

The screw transport picks up the fed clinch stud and conveys it to the setting position.

Function

autoriv fasteners automation a100 fhs setting head press tool press application transfer die tool progressive die clinch stud screw bolt sheet metal component workpiece
Setting head FHS in press tool

Setting process

The setting head is connected to the associated feeding system for press applications and is supplied with clinch studs via a shot hose. The punching head contains a slider that holds exactly one clinch stud. This slider moves the fastener to the setting position. A release signal is then sent to the press. Without a release signal, the press stops.

Main process

The main process co-ordinates the part request to the feeding system. It ensures that the clinch studs are moved to the setting position on time and monitors the press strokes by interrogating the press cams.

Pressing

The clinch stud is pressed into a sheet metal part from the setting position by the press-in mandrel. At the bottom dead center of the press, the slider moves back. If no workpiece is present during a press stroke, blank sensing allows the slider to remain in the home position. This prevents a clinch stud from moving to the setting position, and the press performs the stroke without clinching a stud.

Air supply

A pneumatic connection on the feed system transfers compressed air to the setting head. This connection supplies the permanent air, the pneumatic cylinder for the slider and, optionally, the press-in mandrel.

Technical data

Installation width:

Pneumatic supply:

Control voltage:

Press-in force / path:

Cycle time:

Interfering edge / Possible component depth:

Working direction:

 

*Depending on the fastener and length of the shot hose.

50 / 60 / 70 / 80 mm

6 bar from feeding system

24 V / DC from feeding system

tool-dependent

up to 50 cycles/min*

according to customer requirements

vertical in both directions